Skip to main content

Economics: when does AM make sense?

📍 Where we are: Part 2 · Why and When — Chapter 8 of 11. We have seen what AM is good at and where it is used. Now comes the question every project eventually asks: does it pay?

The simple version

Compare two ways to get cookies. You can buy a custom cookie cutter for a lot of money and then stamp out cookies very cheaply, or you can shape each cookie by hand with no cutter at all, which costs a little more per cookie but needs nothing up front. For ten cookies, hand-shaping wins. For ten thousand, the cutter wins. Somewhere in between is a "break-even" number where the two cost the same. Additive manufacturing is the hand-shaper, and a mold or die is the cutter.

What this chapter covers​

We break the cost of a printed part into its pieces, then compare it with a conventional process that needs expensive tooling, such as injection molding or casting. We work through one illustrative break-even calculation (the numbers are invented for teaching, not measured from any real factory), then look at three things that move the answer: complexity, how full the printer is, and the logic of spare parts.

Where the money goes​

A part's cost is the sum of several kinds of cost. In plain terms:

  • Machine cost — the printer's price spread over the hours it runs. Industrial metal machines are expensive, so their hourly cost is high.
  • Material cost — the powder, resin or filament that ends up in the part, plus the portion wasted or not reusable.
  • Labour — setting up the build, removing parts, and cleaning, support removal and finishing (called post-processing).
  • Design and preparation — turning a model into a build, and in some cases redesigning the part for AM.
  • Quality checks — inspection and testing, which can be a large share for critical parts.

Researchers who built a cost model for two commercial metal machines found the cost per unit of deposited metal to be high, and they noted that unused space in the build chamber makes machine time inefficient, which is why operators try to fit in as many parts as possible [1]. The metal figures in that study (about £2.39 and £6.18 per cm³ for two different processes) are tied to those machines and that year, so they are not a general price list.

NIST (the US National Institute of Standards and Technology) has published a report, Costs and Cost Effectiveness of Additive Manufacturing, which is a good further reading on how AM costs are modelled [2].

The key difference: fixed cost versus per-part cost​

Conventional high-volume processes have a large fixed cost (paid once, regardless of volume), mostly the tool, and a small variable cost (paid for every part). AM has almost no tooling, so its fixed cost is small, but its variable cost per part is higher and falls only slowly as volume grows. The total cost for N parts is simply:

total cost = fixed cost + (variable cost per part × N)

The break-even volume is the N at which the two processes have the same total cost. Below it, AM is cheaper; above it, the conventional process is. One published study compared high-pressure die casting with a metal powder laser process for an aircraft component and found that AM could be economical for the right volume range, and that the saving became large when the part was redesigned to exploit what AM can do [3]. (Die casting is injecting molten metal into a steel mold under pressure.)

A worked example (illustrative, not measured)​

All numbers below are invented for illustration. They are not real quotes, and real values depend heavily on part, material, machine and country.

Suppose we need a small plastic bracket. Injection molding needs a mold costing $20,000 and then $2 per bracket. AM needs no mold and costs $15 per bracket.

Parts madeMolding totalAM totalCheaper
100$20,200$1,500AM
1,000$22,000$15,000AM
5,000$30,000$75,000Molding

The break-even is where $20,000 + $2 × N equals $15 × N, so N = 20,000 ÷ 13, or about 1,540 parts. Under that, print; over it, mold. Notice what the example does not include: the time to get a mold made (often weeks), the risk that a design change makes the mold obsolete, and the cost of storing finished parts. Those can all shift the break-even in AM's favour. It also leaves out finishing work that AM parts might need, which shifts it the other way.

A cost-versus-volume chart with two lines. The additive manufacturing line starts at zero and rises steeply; the molding line starts at 20,000 dollars and rises slowly; they cross at about 1,540 parts. The numbers are illustrative, not measured. Illustrative break-even: AM has no tooling cost but a higher cost per part, so it wins at low volume; molding has a high up-front cost but a low cost per part, so it wins at high volume. Original diagram by the authors, created with AI assistance.

What shifts the break-even​

Complexity​

In the example, we assumed the same bracket either way. But if the part is complex, a conventional process may need several operations or a more complicated, more expensive tool, while AM's cost barely changes. Complexity pushes the break-even toward higher volumes for AM, which is the economic side of "complexity is almost free" from the earlier chapter.

How full the machine is​

Because a build takes time whether the chamber is half empty or packed, cost per part falls when you fill the build space. The cost study mentioned above found that although AM has no tooling to amortise, economies of scale can still be achieved, and that using only part of the build volume makes operation inefficient [1]. In practice, a service bureau (a company that prints parts for others) groups many customers' parts into one build.

Spare parts and the digital warehouse​

Companies keep warehouses of rarely used spare parts, with a cost for storage, for obsolete stock and for waiting when a part is out of stock. Researchers have studied replacing some physical stock with digital files and local printing. A scenario study of aircraft spare parts found that distributed AM production would be viable only if equipment costs and production times fell, and reported lower logistics costs, particularly for transport [4]. Another scenario study, using data from the literature, found that AM could reduce the safety inventory (the buffer stock kept against shortages) of aircraft spare parts [5]. So the logic is real but not automatic: it works best for parts that are expensive, rarely needed, hard to source and not safety-certified.

A short decision checklist​

  1. How many parts? Dozens to hundreds favour AM; many thousands usually favour conventional tooling.
  2. How complex? Internal channels or consolidated assemblies favour AM.
  3. Does each part differ? Customized parts favour AM.
  4. How urgent? Needing a part within days, with no time for tooling, favours AM.
  5. Is certification required? If yes, include the cost and time of qualification.

Why it matters​

Technology choices that look exciting often fail the cost test, and technology choices that look dull can pass it. Understanding fixed versus per-part cost lets you do a rough check in minutes, which is the first filter any engineer or manager applies.

In the real world​

Real quotes are more complicated than our example: price breaks by volume, discounts for full builds, material premiums, and finishing. The structure of the calculation, however, is always the same: fixed cost plus per-part cost times quantity.

Key terms​

  • Fixed cost — a cost paid once regardless of how many parts are made, such as a mold.
  • Variable cost — a cost paid again for each part, such as material and machine time.
  • Break-even volume — the number of parts at which two processes have the same total cost.
  • Tooling — the molds, dies and fixtures needed before conventional production can start.
  • Die casting — forming metal parts by injecting molten metal into a steel mold under pressure.
  • Injection molding — forming plastic parts by injecting molten plastic into a mold.
  • Post-processing — work done after printing, such as removing supports, cleaning, machining and polishing.
  • Utilization — how much of the machine's time and build space is actually used to make parts.
  • Service bureau — a company that prints parts for other companies.
  • Spare parts — replacement components kept in stock for repairs, often needed rarely and unpredictably.

Where this leads​

Enough theory: your first print puts a real desktop printer in front of you and walks through making something.