RepRap and the open-hardware movement
📍 Where we are: Part I · Roots — Chapter 1 of 16. The preface drew the map of the open stack; this chapter tells how the bottom layer, the machine itself, became open in the first place.
Imagine a bread-making machine that could bake the parts for a second bread-making machine, and the plans were free for everyone. Anyone who got one could build more and give them to friends, and each owner could improve the plans. That was the idea behind RepRap: a 3D printer that prints much of itself, shared freely, so that machines spread the way ideas do instead of the way products do.
What this chapter covers
We follow open 3D printing from the RepRap project at the University of Bath, through the first self-copying machines, the end of a key patent, MakerBot's closing of the Replicator 2 design, and the Prusa lineage, up to the present, where some of the open projects have started to narrow their own openness. Dates are given where we could verify them; where a source only gives a year, we say so.
RepRap: a printer that makes its own parts
RepRap began under Adrian Bowyer at the University of Bath, England. Sources date the start differently: the project's own 2011 paper places it in 2004 [1], while the Science Museum Group's catalogue entry for the original "Darwin" machine, which credits Bowyer and Ed Sells, gives 2005 [2]. This chapter's timeline uses 2005, the museum's date, and the table below notes the conflict. Its project site describes it as "humanity's first general-purpose self-replicating manufacturing machine" [3]. The goal was not to make a perfectly self-sufficient robot. The machine prints many of its own plastic parts, and a person adds the bought parts (motors, rods, electronics, which RepRap folk call "vitamins") and assembles the copy [3]. The RepRap wiki states that the project is distributed under the GNU General Public License (GPL) [4].
The project's own 2011 paper in Robotica describes the reasoning, the processes used to build the machine and the way components evolved, and estimated "about 4500 machines in two and a half years" in the world [1]. That is the authors' estimate, not a count from sales records.
Milestones
We list only dates confirmed in a project, museum, company or journal source; several widely repeated early dates are left out because we found them only in secondary sources.
| Date | Event |
|---|---|
| 2005 | Bowyer starts the project at the University of Bath [2] (the RepRap wiki also says RepRap was first introduced online in February 2004 [4]; the sources differ, so we give no single start date) |
| 29 May 2008 | The first complete working "child" machine, produced by its parent RepRap, is shown at Bath at 14:00 UTC [4] |
| January 2011 | The Robotica paper appears, estimating about 4500 machines [1] |
| May 2012 | First commit to the Prusa i3 design repository [5] |
| 20 and 24 September 2012 | MakerBot blog posts of these dates, linked from the RepRap wiki, are at the centre of the dispute over the Replicator 2's closed files [6] |
| 19 June 2013 | Stratasys announces its merger with MakerBot [7] |
The patent that expired, and the timing
Fused filament fabrication was claimed in US Patent 5,121,329 by S. Scott Crump, assigned to Stratasys. It was filed on 30 October 1989 and granted on 9 June 1992 [8]. Google Patents lists an anticipated expiry of 30 October 2009 and warns that its dates are assumptions rather than legal conclusions [8]. It is widely told that the expiry opened the market to low-cost machines. The timing is suggestive, since RepRap kits were already circulating, but we did not find a primary source that measures the patent's effect, so we do not claim a cause.
MakerBot: a commercial branch that closed
MakerBot was "founded in 2009" and based in Brooklyn, according to Stratasys's own press release [7]. We did not find a primary source in this session for MakerBot's earlier licences (for example for the Cupcake or Thing-O-Matic), so we make no licence claims for those machines. With the Replicator 2 in September 2012, the RepRap wiki records, MakerBot released its firmware, driver, slicing engine and electronics firmware but not the Replicator 2 body design files or the MakerWare GUI, which started a public dispute [6]. That page is a community record, not MakerBot's own statement. Stratasys announced on 19 June 2013 an all-stock merger with MakerBot: about 4.76 million Stratasys shares, initially valued at about $403 million, plus performance-based payments of up to 2.38 million more shares, valued at up to $201 million at the same share price [7].
Open-lineage milestones (upper lane: RepRap, the Robotica paper, the Prusa i3) set against company and patent events (lower lane: MakerBot, the FDM patent expiry, the Replicator 2).
Original diagram by the authors, created with AI assistance.
The Prusa lineage
Josef Průša, who had worked on RepRap, designed the Prusa i3. Its RepRap wiki page records the first commit to the design repository in May 2012 and a "Final refactoring complete" note on 3 September 2012; the design is GPL, and an official kit from Prusa only became available in May 2015 [5]. Prusa's own company page says that he joined the RepRap project in 2009 and founded Prusa Research as a one-person start-up in 2012 [9]. The company later became one of the best-known makers of printers that came with published designs, and its slicer is released under the AGPL-3.0 licence (see the PrusaSlicer repository cited in the preface).
Openness narrows again
The story is not a one-way march to openness. On 19 December 2025 Prusa released the CAD files for the CORE One and CORE One L frames under a new Open Community License (OCL). The licence allows study, modification, shared modifications under the OCL, and use in your own workshop or production line, but it does not allow selling complete machines or remixes based on the files without a separate agreement. The firmware and PrusaSlicer remain GPL, per Prusa's post, which also says the patents and licence terms are meant to stop industrial clones rather than home workshops (a statement of the company's own position) [10]. Whether such terms count as "open source" is contested; we return to this in Chapter 2.
Why it matters
RepRap showed that a complex machine can be developed by a distributed community when its designs are free to copy, and a 2012 Science commentary argued that open-source 3D printers combined with open microcontrollers can produce laboratory equipment at lower cost [11]. It seeded the desktop 3D-printing industry in the sense that the Prusa line grew from it, though we do not quantify that. The same history also shows the tensions that remain: a company can start open and later close, and another can narrow its openness, as Prusa did for the CORE One CAD files in 2025. Knowing the dates and licences lets you tell what you actually get with a given printer.
In the real world
When you read a spec sheet that says "open source", ask which part: the frame design, the electronics, the firmware or the slicer. RepRap is distributed under the GPL per its wiki, and the Prusa i3 design is recorded as GPL on its RepRap wiki page. A modern purchase decision often turns on exactly this question, and the answer can differ for the same company between two product generations.
Key terms
- RepRap — "replicating rapid prototyper"; the open project, begun in 2004–2005 (sources differ), for a printer that prints many of its own parts.
- Self-replication — a machine producing the parts needed to build another like it; in RepRap, the printed parts but not motors, electronics or fasteners.
- Vitamins — the non-printable bought parts of a RepRap machine, such as motors and electronics.
- FDM / FFF — fused deposition modeling and fused filament fabrication, two names for melting plastic filament and laying it down layer by layer; the RepRap paper lists "fused-filament fabrication" among its keywords.
- Patent expiry — the end of a patent's term, after which anyone may use the claimed invention.
- Open Community License (OCL) — Prusa's 2025 licence for CORE One CAD files, which permits shared modification but not selling machines built from the files without agreement.
- Kit — a printer sold as parts to assemble.
Where this leads
Whether a design is "open" depends on its licence, so the next chapter covers licenses and the economics of openness.