Preface — AM Processes, Materials & Design
📍 Where we are: Preface (unnumbered) — Book 2 of the series. Book 1 explained what additive manufacturing is and why you might use it; this book opens the machine and asks how each process really works.
Book 1 was a tour of the kitchen: here is the oven, here is the stove, here is what a meal looks like. Book 2 is cooking school. You learn why bread rises in an oven but not on a stove, what changes when you swap flour for rice, and how to write a recipe that the oven can actually follow. To keep it concrete, we cook the same dish all the way through: one small mounting bracket, considered for every process in turn.
What this chapter covers
This preface says who the book is for, introduces the running example, explains how each chapter is laid out, lists the conventions we use, and gives a map of the four parts. It is deliberately short. There is no process physics here; that starts in the next chapter.
Who this book is for
You should be comfortable with the ideas of Book 1 Additive Manufacturing Fundamentals: that additive manufacturing (AM) builds parts by adding material, usually layer by layer, and that the international vocabulary standard ISO/ASTM 52900 sorts processes into seven categories [1]. If you can say in a sentence what "powder bed fusion" or "vat photopolymerization" means, you are ready. If not, a quick read of the first chapters of Book 1 will repay itself.
You do not need to be a materials scientist or a mechanical designer. We use plain-language analogies first and then give the precise version, but we assume you can follow a simple equation, a table of properties, and the idea that a polymer and a metal behave differently when heated.
A short recap of what we take from Book 1:
- Layer-by-layer building from a digital model, which gives design freedom but also a built-in direction (the build direction, usually called Z).
- Seven process categories; this book covers the ones used most often to make real parts: material extrusion, vat photopolymerization, powder bed fusion, material jetting, binder jetting and directed energy deposition, plus sheet lamination in brief.
- The workflow from CAD to a finished part: slicing, printing, removal, post-processing and inspection.
The running example: one bracket
Every process chapter ends by asking the same practical question about the same part. Our part is a lightweight mounting bracket: a small plate-and-rib component that holds a sensor module to a frame, with two bolt holes, one load-bearing rib and a modest load. The example is invented for teaching, and every number that appears in connection with it is labelled illustrative: nothing about the bracket was measured.
Why a bracket? Brackets are among the most common real AM parts, and they let us ask honest questions that differ from process to process:
- In extrusion, which way should it lie so the load does not pull the layers apart?
- In a resin vat, can the rib be thin without breaking when it is peeled from the vat window?
- In a polymer powder bed, can we nest fifty brackets in one build and skip supports?
- In a metal laser machine, where do supports and the build plate attach, and what must be machined afterwards?
We use the bracket lightly: a short "bracket check" paragraph in each chapter, never a case study. The aim is to show that the right answer changes with the process, not to optimise one part to perfection.
How the chapters are built
Each chapter follows the same shape so you can find things quickly:
- A banner saying where you are in the book.
- The simple version, an everyday analogy.
- What this chapter covers.
- Three to five content sections with the physics, the materials, and the limits.
- One hero figure, drawn by hand as an SVG, showing a cross-section or a map of the idea.
- Why it matters, In the real world, Key terms, and Where this leads.
Citations appear as small bracketed numbers such as [2]; the numbers restart in each chapter and point to that chapter's block on the references page.
A map of the book
The figure below shows the four parts and the order of the fifteen chapters.
- Part I, Polymer Processes (chapters 1-4): material extrusion, vat photopolymerization, polymer powder bed fusion, and material and binder jetting.
- Part II, Metal and Ceramic Processes (chapters 5-8): laser powder bed fusion, electron beam melting and directed energy deposition, metal binder jetting and print-and-sinter routes, and ceramics, composites and other material families.
- Part III, Design for AM (chapters 9-11): design rules, topology optimisation and lattices, and supports, orientation and build preparation.
- Part IV, Making It Real (chapters 12-15): post-processing, quality and inspection, standards and qualification, and finally how to choose a process.
The book map: four parts, fifteen chapters, with one lightweight bracket threading through the process chapters.
Original diagram by the authors, created with AI assistance.
You can read straight through, but the process chapters in Parts I and II are largely independent. If you only need one process, read its chapter, then jump to Part III. The later books continue the story: Book 3 looks at open-source hardware and software, and Book 4 at research frontiers and industrial challenges.
Conventions
- Illustrative numbers. When a number is made up to show an idea, we say "illustrative". When a number comes from a source, it carries a citation. Typical values for materials and machines vary between suppliers and machines, so treat them as orders of magnitude, not specifications.
- Process names. We use the ISO/ASTM 52900 category names and give common trade or abbreviation names (FFF, SLA, SLS, MJF) in parentheses [1].
- Units. SI units, with micrometres written µm.
- Figures. Labels in figures are short English technical terms so that the same figure serves every language edition.
Why it matters
Choosing and using an AM process well is rarely about the machine that sounds most impressive. It is about matching a physical mechanism (melting and fusing, curing with light, gluing with a binder) to a material, a geometry and a requirement. Reviews of AM in engineering repeatedly point out that the lack of design principles and standardised practice, not the lack of machines, is what holds good engineering back [2]. This book aims at that gap.
In the real world
The same bracket-shaped problem appears in every industry that has adopted AM: a part that is small, geometrically awkward to machine, needed in low volume, and expensive when it fails. The chapters ahead show the different answers that extrusion, vat, powder bed and jetting processes give to it, and why a polymer designer and a metal designer talk past each other unless they share this vocabulary. For a broad review of polymers across all these processes see [3].
Key terms
- Additive manufacturing (AM) — making parts by joining material, usually layer upon layer, from a 3D model; the formal name for what is often called 3D printing.
- Process category — one of the seven ISO/ASTM 52900 families of AM processes, defined by how material is added and bonded.
- Build direction (Z) — the direction in which layers are stacked; many properties differ along it.
- Running example — the lightweight mounting bracket used throughout Book 2 to compare processes; invented for teaching.
- Illustrative number — a value chosen to explain an idea, not a measurement or a specification.
- Hero figure — the main hand-drawn diagram at the centre of each chapter.
- Design for AM (DfAM) — shaping a part to suit an AM process's strengths and limits (Part III).
Where this leads
Part I begins with the process most readers have met first: Material extrusion (FFF/FDM).