Material extrusion (FFF/FDM)
📍 Where we are: Part I · Polymer Processes — Chapter 1 of 15. The preface set up the book and the bracket; this chapter starts with the most familiar process, where a hot nozzle draws a part in molten plastic.
Think of a hot glue gun mounted on a robot arm. The gun melts a stick of glue and squeezes out a thin bead; the robot lays the bead down in the shape of a slice, then lifts the gun a little and draws the next slice on top. Where the new bead touches the warm old one, the two melt together a bit and stick as they cool. The stick is a bead only as strong as the join, and the joins between layers are the weak points.
What this chapter covers
We follow the plastic from filament spool to finished part: what happens inside the hotend, how a freshly laid bead (a "road") bonds to its neighbours, why the result is stronger along the road than across the layers, and which materials are used. We end with fibre-reinforced and pellet-fed variants and a bracket check. Material extrusion is the ISO/ASTM 52900 category for processes in which material is selectively dispensed through a nozzle or orifice [1]; the name FFF (fused filament fabrication) and the trademarked FDM (fused deposition modeling) are the common names for the filament version.
Inside the hotend
A material-extrusion printer has three jobs: push, melt and place.
- Push. A motor-driven drive gear grips the solid filament (typically 1.75 mm or 2.85 mm in diameter) and feeds it into the hot end. The filament acts as a piston, pushing the molten plastic ahead of it.
- Melt. A heated block, often called the liquefier, raises the filament above its melting or glass-transition temperature. Heat has to travel inward from the wall, so a fast print and a thick filament mean the core may not be fully melted when it leaves. A short "cold" zone above the heater (the heat break) keeps the filament solid so that it can still be pushed.
- Place. The molten plastic is forced through a nozzle (a common diameter is 0.4 mm) and the printer moves the nozzle, or the bed, to deposit a road, whose width is a little larger than the nozzle diameter because the extrudate swells and is pressed flat by the nozzle.
The modelling literature breaks this into the pieces we have just named: the torque needed to feed filament, heat flux into the liquefier, shear and pressure drop in the melt, die swell, and cooling and spreading of the road [2]. Because molten polymers get thinner under shear (they are shear-thinning), pressure drop depends strongly on temperature and flow rate; this is why printing too fast at too low a temperature produces under-extrusion.
How roads bond
The finished part is only as good as the joins. When a hot road touches a neighbour or the layer below, three things compete:
- Contact growth. The round road sags and flattens against the surface, widening the contact.
- Neck growth (sintering). Polymer flows across the interface and a "neck" forms; this is driven by surface tension and happens only while the material is hot enough.
- Chain interdiffusion. Polymer molecules wriggle across the boundary and entangle, which is what gives real strength.
All of this stops as the road cools. Studies of ABS filaments found that the thermal history, set by the printing strategy, the temperature of the build envelope and the heat-transfer coefficient, controls the mesostructure and bond strength between filaments; sintering mattered only for the short time the filament stayed above a critical sintering temperature [3]. That is why heated chambers help with warping-prone and high-temperature polymers, and why a layer printed on a layer that has already gone cold bonds poorly.
Anisotropy: strong along, weak across
A printed part is a bundle of roads. Along a road the polymer is continuous; between roads and between layers it relies on the necks. The result is anisotropy: properties depend on direction. In a classic study of ABS made with raster orientation, air gap, bead width, colour and model temperature varied, typical tensile strength was 65 to 72 percent of injection-moulded ABS for parts built with a small overlap between roads [4]. Reviews note layer boundaries as the weak regions and describe the anisotropy as highly dependent on material and process parameters [5]. In practice: pull along the layers and the part behaves like a bundle of fibres; pull perpendicular to them (in Z) and it can split between layers at a fraction of that strength.
Materials
| Family | Examples | Why you would choose it |
|---|---|---|
| Entry-level thermoplastics | PLA, ABS, HIPS | Cheap, easy to print; PLA is the default for desktop use |
| Engineering thermoplastics | PETG, PC, polyamides (PA, "nylon") | Tougher, more heat or chemical resistance |
| High-performance thermoplastics | PEI, PEEK, PEKK | High service temperature and strength; need hot nozzles and heated chambers |
| Composites | Short-fibre filled, continuous-fibre | Higher stiffness and strength in the fibre direction |
Reviews list ABS, PLA, PC and HIPS as typical FDM materials, with a resolution of about 100 to 150 µm and the advantage of inexpensive machines and materials; the disadvantages named are rough surfaces and a high-temperature process [5].
PEEK and similar semi-crystalline polymers add a complication: they crystallise as they cool, so anything that changes the cooling history also changes crystallinity and microstructure [6]. For PEEK, the semi-crystalline nature and high melting temperature make the result highly sensitive to processing conditions, which a review links to the large spread of reported properties in the literature [7].
Fibre-reinforced and pellet extrusion
Chopped fibres (typically carbon or glass) mixed into the filament raise stiffness along the flow direction but do not cure the weak interlayer joins; they can make them worse. Continuous fibre systems lay a fibre tow inside the road, giving much higher stiffness and strength along the fibres; a review finds they outperform printed pure plastics but still cannot compete with conventionally processed composites, because of defects and a low fibre volume fraction [8]. Pellet extrusion replaces filament with a screw extruder fed with granules, as used in conventional moulding; it suits large parts and cheaper feedstock, with a coarser road size.
Process limits to remember
- Surface finish and resolution. Visible layer lines ("stair-stepping") and rounded corners, because the road is a rounded bead.
- Warping. Roads shrink as they cool; large flat parts curl off the bed.
- Supports. Overhangs need supports, which leave marks (see the later chapter on supports and build preparation).
- Speed. Volume is limited by how fast heat can be pushed into the melt.
Filament is pushed through a heated nozzle and laid as roads that fuse by neck growth; the necks between layers are the weakest direction.
Original diagram by the authors, created with AI assistance.
Bracket check
Lay the (illustrative) bracket flat so that the load runs along its roads, not across layers. Mounting holes should have walls of several perimeters, not just infill. A fibre-filled filament would stiffen it in the plane; a high-temperature polymer would let it survive near a warm component. Remember that the plate is strong along the roads and weaker across: if it ever sees a pull-off load, orientation is more important than material.
Why it matters
Material extrusion machines are inexpensive, widely available and forgiving, so they are where most people first meet AM. They also teach the central lesson of the whole field: the process makes the material. The same pellets, printed in two orientations or two chamber temperatures, give two different parts.
In the real world
Desktop printers make fixtures, jigs and prototypes. Industrial machines handle high-performance polymers such as PEI and PEEK, and large pellet-fed systems print big, low-cost parts. Industrial users usually specify orientation, chamber temperature and a printed test coupon, because the property variation described above is large.
Key terms
- Material extrusion — AM process category where material is selectively dispensed through a nozzle or orifice.
- FFF / FDM — fused filament fabrication / fused deposition modeling; the filament form of material extrusion (FDM is a trademark).
- Hotend — the assembly of heat break, heater block and nozzle that melts and extrudes the filament.
- Road — a single bead of extruded material, the "pixel" of the process.
- Neck growth — the widening contact between two hot roads as the polymer flows and fuses across their interface.
- Interdiffusion — polymer chains moving across an interface and entangling, which gives bond strength.
- Anisotropy — properties that depend on direction; in FFF, weakest across layers.
- Shear-thinning — a polymer melt becoming less viscous as it flows faster.
- Pellet extrusion — material extrusion fed with granules through a screw instead of filament.
- Continuous-fibre composite — a printed part with an unbroken fibre tow laid inside the roads.
Where this leads
Next: Vat photopolymerization (SLA, DLP, LCD), where light, not heat, makes the layer.