Post-processing
📍 Where we are: Part IV · Making It Real — Chapter 12 of 15. Part III showed how to design, orient and prepare a build. This chapter follows the part out of the machine and through the steps that turn a raw print into a finished component.
A printed part leaving the machine is like a loaf of bread leaving the oven stuck to its tin, still hot inside and dusted with flour. You still have to get it out of the tin, let it settle, trim it, and finish the crust. Additive manufacturing (AM) is the same: the part is stuck to a plate or buried in powder, it carries hidden internal strain, and its surface is rough. Post-processing is everything between "the machine stopped" and "the part is ready to use", and it is often a larger share of the work than the print itself.
What this chapter covers
We follow the running example, a lightweight mounting bracket, through a typical sequence: removing loose powder or resin, relieving internal stress, cutting the part off its plate, taking off supports, heat treating or hot isostatic pressing (HIP), machining the surfaces that matter, and finishing the rest. We cover the metal chain first, then the polymer chain. The goal is to show why the order of steps matters and why designers must plan for these steps from the start (see Design for AM and Orientation, supports and build preparation).
The metal chain, in order
The bracket is built by laser powder bed fusion (see Laser powder bed fusion). A typical order is below; real routes vary by alloy, customer and specification.
- Depowdering. Loose powder is brushed, blown or vacuumed out of the part and its channels, usually in an enclosed station so the powder can be recovered and reused. Internal channels and lattices trap powder, which is why DfAM asks for drain holes.
- Stress relief, still on the plate. During a build, each thin layer cools quickly while attached to a colder body below it, so the finished part holds residual stress (locked-in internal force) [1]. If the part were cut free first, it could spring out of shape. So the plate, with the parts still attached, usually goes into a furnace first. In a study of laser powder bed fusion Inconel 625, a stress-relief treatment of 870 °C for 1 hour effectively reduced residual stress [2]. The right temperature depends on the alloy and the specification; ASTM F3301 is a specification for thermal post-processing of metal parts made by powder bed fusion [3].
- Removal from the plate. Parts are usually cut off with wire electrical discharge machining (wire EDM, a thin electrified wire that erodes the metal) or a saw. Cutting disturbs the stress balance, which is another reason to relieve stress first.
- Support removal. Supports are cut, broken or machined away. Each support leaves a rough witness mark, so supports are best placed on surfaces that will be machined anyway.
- Heat treatment and HIP. Heat treatment tunes the microstructure (the grain-scale structure of the metal) to give the required strength and ductility. Hot isostatic pressing (HIP) puts the part in a vessel at high temperature and high gas pressure, which squeezes internal pores shut. A tomography study of electron-beam-melted Ti-6Al-4V found that HIP shrank all internal porosity below the resolution limit of about 5 µm, apart from defects with surface-connected ligaments [4]. The reason is simple: gas pressure squeezes a closed pore from outside, but a pore open to the surface is filled by the same gas and cannot collapse.
- Machining. Critical features such as bolt holes, bearing seats and sealing faces are finished by conventional machining to a tolerance AM cannot reliably deliver as built. Plan machining allowance (extra material, designed in) on these faces.
- Surface finishing. Blasting, tumbling, vibratory finishing, polishing, electrochemical polishing and laser polishing all smooth the surface. Reviews describe as-built metal AM surfaces as markedly rough (staircase effect, partially fused powder, balling, spatter), with values that vary widely by process, material and surface orientation [5] [6]. Mechanical methods struggle to reach internal channels and fine lattices, and electrochemical polishing helps there but must be controlled [5].
The metal post-processing chain for the bracket: stress relief comes before cutting the part off the plate, and HIP cannot close pores that are open to the surface.
Original diagram by the authors, created with AI assistance.
Why the order matters
Two rules explain most of the sequence. First, relieve stress before releasing the part, or it may distort. Second, finish last what is easy to damage: machining and polishing come after HIP and heat treatment, because heat treatment can move or scale the part. HIP does not change surface roughness, so fatigue-critical surfaces still need finishing after it. Surface roughness and near-surface pores matter for fatigue life [7] [8].
The polymer chain
Polymer parts follow a shorter, gentler route, but the ideas are the same.
- Powder bed fusion (nylon-type parts). The part is dug out of the powder cake and cleaned by blasting. The surface can be dyed, tumbled or coated.
- Vat photopolymerization (resin). The part is washed in solvent to remove uncured resin, supports are clipped off, and the part is post-cured (exposed to light, often with heat) to finish the chemical reaction. Details are in Vat photopolymerization.
- Material extrusion. Supports are snapped or dissolved, then parts can be sanded, filled and painted.
- Vapour smoothing. A solvent vapour melts the outermost skin so it flows level. In one peer-reviewed study of nylon 12 parts from laser sintering, optimised hot chemical vapour smoothing reduced Ra from 11.92 to 3.45 µm [9]. Vendor claims of lower values exist but were not verified here. Thin sections can deform, so test on a sample first.
Cost and planning
Post-processing is real labour and furnace time, not an afterthought. Cost studies of AM break total cost into machine, labour and material [10] [11] (one cost model identifies low deposition rates and high specific cost as the central impediments for metal AM), and manual finishing falls under labour. For the bracket, the sensible questions are: which faces must be machined, can supports be placed there, and is HIP required by the application? If the answers are "two faces", "yes" and "no", the route is short; if the bracket is flight-critical, the route lengthens (see Standards, qualification and certification). All of this can be changed by design, which is why post-processing belongs in the design review.
Why it matters
The properties a customer buys are the properties after post-processing, not the as-printed ones. Skipping or reordering a step can cause distortion, trapped powder, a rough fatigue-initiating surface or an out-of-tolerance hole. Post-processing is also where much of the hidden cost lives.
In the real world
Production sites run post-processing as a defined, documented chain with traceability, since each step changes the part. Inspection after the chain, described in Quality, inspection and non-destructive testing, is how the result is confirmed.
Key terms
- Depowdering — removing loose, unmelted powder from a printed part and its internal channels.
- Residual stress — internal force locked into a part by uneven heating and cooling during the build.
- Stress relief — a furnace cycle that lets residual stress relax before the part is removed from its plate.
- Wire EDM — cutting metal with a thin electrified wire; commonly used to separate parts from the build plate.
- Support removal — cutting, breaking or machining away the temporary structures that held the part during the build.
- Hot isostatic pressing (HIP) — treating a part at high temperature and gas pressure to close internal pores.
- Machining allowance — extra material designed into a surface so it can be machined to final size.
- Post-curing — light and heat exposure that completes the reaction in a resin part after printing.
- Vapour smoothing — melting a polymer part's outer skin with solvent vapour so it flows smooth.
- As-built — the state of a part straight off the machine, before post-processing.
Where this leads
Once the part is finished, how do you know it is good? That is the subject of Quality, inspection and non-destructive testing.