Skip to main content

Orientation, supports and build preparation

📍 Where we are: Part III · Design for AM — Chapter 11 of 15. You now have a printable, perhaps optimized shape. Before pressing "print" someone must decide how it sits on the plate, what holds it up, and how it shares the build. This chapter covers that planning step, which closes Part III.

The simple version

Think of packing a suitcase for a long trip. You decide which way each item lies, what needs padding so it does not break, and how to fit many things together without wasting space. You also guess how long the packing will take and what the baggage will cost. Build preparation is the same: orient each part, add supports (the padding), nest parts together, and estimate time and cost. Modern software can even "pre-bend" the part to cancel the warping it expects.

What this chapter covers​

We cover five decisions: orientation and its trade-offs, supports (their jobs, types and removal), nesting (several parts on one plate), build time and cost estimation, and simulation-assisted distortion compensation. The examples use powder bed metal, where these choices matter most, and the lightweight bracket as the running example.

Orientation: the first and biggest decision​

Orientation is how the part is rotated relative to the build plate and the build direction. Because AM builds in layers, it affects almost everything:

Orientation affectsWhy
Support volumeDown-facing surfaces below the angle limit need support (see design for additive manufacturing).
Build height and timeTaller builds mean more layers, and each layer costs recoating and scanning time.
Distortion and residual stressLarge flat or long areas along a layer shrink more as they cool.
Surface qualityDown-facing and supported surfaces are rougher; up-facing and vertical surfaces are usually better.
Mechanical propertiesLayered parts are often anisotropic, so load direction versus build direction matters.

These pull against each other. Optimisation studies weigh support volume against geometric errors and tolerances [1], and distortion adds a further pull: fewer supports and shorter builds can mean more residual distortion, so orientations are often compared on predicted distortion [2]. Where possible, choose an orientation that self-supports rather than relying on supports to rescue a poor one (a design principle from the previous chapter, also covered in textbooks such as [3]). There is rarely a single "best" answer; the critical surface or the critical load direction usually decides.

Supports: what they do and what they cost​

Supports in powder bed metal have more jobs than holding up overhangs. They anchor the part to the plate against thermal pulling, and they conduct heat away. More support means less thermal deformation, but also more material, longer printing and more post-processing [1]; the anchoring and heat-conduction roles follow from how residual stress builds up [4][5].

Three panels showing one L-shaped bracket lying, standing with supports under its arm, and tilted, plus four trade-offs and a build preparation step. The same bracket lying, standing or tilted changes support volume, height, distortion and surface finish, and build preparation then handles nesting, estimates and simulation. Original diagram by the authors, created with AI assistance.

Types​

  • Block supports are solid or lightly perforated walls under a surface. Their geometry, for example perforation, has been studied for overhangs in aluminium and titanium alloys [6].
  • Lattice or web supports use thin repeating structures that save material and are easier to break away [7].
  • Tree or cone supports touch a surface at a few points, saving material. (These two descriptions are general, not drawn from the sources cited here; build-preparation software offers several more types.)

Recent research designs supports with simulation (numerical demonstrations, i.e. lab-scale evidence). A 2024 method optimises support topology with an inherent-strain distortion model while enforcing self-support, minimum length scale and easy removal [8], and a 2023 method adds distortion and overheating constraints to self-supporting topology optimisation of the part itself [9]. A review catalogues the wider support literature [1].

Removal​

Supports are usually cut or broken off, then the surface is machined or finished. Teeth or perforations at the contact make removal easier but leave marks. Supports that sit inside internal channels may be unreachable, which is why design rules avoid them (see post-processing). Removal is also a cost: it is manual, skilled work, and often limits how many parts you can economically print.

Nesting​

Nesting places many parts on one plate. The goals are to fill the build volume so the fixed costs of a build are shared, keep spacing for powder flow and support access, and avoid placing tall parts in a way that shadows others from the gas flow. Software does it automatically, but you set the rules. Considerations such as keeping parts out of the gas-flow shadow are specific to the machine; check the vendor's guidance.

Estimating time and cost​

A rough build estimate includes machine time (set by the number of layers and the scanned area per layer), material (part plus supports plus powder lost), preparation, post-processing and inspection. Because orientation changes height and support volume, it changes both time and cost [3]. Most build-preparation software provides an estimate, but it is only as good as its machine model, so compare a few early estimates with actual builds. For a numerical example you would need your own quotes; none is given here.

Simulation-assisted distortion compensation​

Metal parts warp as they cool, because the melted layers contract against the cooler material below. Process simulation predicts this [5]: one fast approach is the inherent strain method, where shrinkage per layer, calibrated from a detailed process simulation, is applied to a finite-element model of the part [10]. The predicted distortion can be used in two ways:

  1. Compare setups. Test orientations and supports on the computer before printing. Distortion constraints now also enter the topology optimisation of parts and supports [9][8], and a review of distortion and residual stress summarises influencing factors and mitigation [2].
  2. Compensate. Print a deliberately pre-distorted shape so that the result lands on the intended geometry. Mitigation approaches are surveyed in [2]; many simulation packages offer a compensation function (check your vendor).

Compensation relies on repeatable behaviour; if the process changes (powder lot, machine, scan strategy), the model must be recalibrated. Always inspect the first builds.

The bracket test​

For the bracket, lying with its long arm on the plate gives a short build and little support but a larger footprint and a rough underside. Standing it upright shrinks the footprint and allows more brackets per plate, but supports are needed under the arm and the build is taller. A tilted orientation could balance the two. A simulation could compare distortion for the three, and a pre-distorted version could then be printed if the mounting faces must be flat. The choice also depends on which face must be machined.

Why it matters​

Orientation and supports often decide whether a build succeeds and what it costs. A good build plan reduces warping, scrap and post-processing before any powder is melted.

In the real world​

Build-preparation software combines automatic nesting, support generation and cost estimates, and simulation tools add distortion prediction. Research is moving toward simulation-based support design [8][9]. The reviews cited here are academic, so check any claim against your own machine.

Key terms​

  • Build orientation — how a part is rotated relative to the plate and build direction.
  • Support structure — sacrificial material that anchors a part, holds up overhangs and conducts heat.
  • Block support — a solid or lightly perforated support wall.
  • Nesting — arranging several parts on one build plate.
  • Residual stress — stress locked into a part by uneven heating and cooling.
  • Distortion — change in shape caused by residual stress, often on cutting a part from the plate.
  • Inherent strain method — a fast simulation approach that applies layer shrinkage to a finite-element model.
  • Distortion compensation — printing a pre-deformed shape so the result matches the intended geometry.

Where this leads​

After printing come the steps that turn a part from the plate into a finished component: post-processing.